1、机械CE认证标准-C类标准

EN ISO 3691-3:2016

Industrial trucks — Safety requirements and verification Part 3: Additional requirements for trucks with elevating operator position and trucks specifically designed to travel with elevated loads (ISO 3691-3:2016)

工业卡车-安全要求和验证-第3部分:具有升降操作人员位置的卡车和专门设计用于升降负载的卡车的附加要求(ISO 3691-3:2016)

 

 

2、EN ISO 3691-3:2016适用工业车范围Scope

This part of ISO 3691 gives safety requirements and the means for their verification, additional to those of ISO 3691-1, for industrial trucks with a vertical, non-tilting mast:

上海郜盟提示ISO 3691的这一部分除了ISO 3691-1的安全要求外，还提供了具有垂直、非倾斜桅杆的工业卡车的安全要求和验证方法:

a) those trucks having an elevating operator position, and order‑picking trucks, as defined in ISO 5053-1, where the elevating operator position and the load‑handling device lifts to a height of more than 1 200 mm above ground level;

a) 上海郜盟提示：具有升降操作员位置的卡车，以及ISO 5053-1中定义的接单卡车，其中升降操作员位置和负载处理设备上升到高于地面1200mm的高度;

b) lateral- and front-stacking trucks, as defined in ISO 5053-1, designed to travel with a load-handling device elevated more than 1 200 mm above ground level, with the load-handling device elevated, lowered or laterally displaced, laden or unladen, while the truck is travelling. These trucks are designed to travel indoors on a smooth, level surface (e.g. concrete) and can be guided, unguided, or both, when in use; they are not intended to tow or push.

b) 上海郜盟提示：ISO 5053-1中定义的横向和前方堆垛卡车，其设计目的是在卡车行驶时，将负载处理装置升高到高于地面1200mm以上，负载处理装置升高、降低或横向位移，装载或卸载。这些卡车被设计成在室内光滑、水平的表面(例如混凝土)上行驶，在使用时可以引导、无引导或两者兼有;它们不是用来拖或推的。

This part of ISO 3691 is not applicable to stacker trucks which handle two loads, one on the forks and the other on the support arms, this type of truck being covered by ISO 3691-1.

上海郜盟提示ISO 3691的这一部分不适用于处理两个负载的堆垛车，一个在叉上，另一个在支撑臂上，这种类型的卡车被ISO 3691-1覆盖。

It is not applicable to trucks with an elevating operator position up to and including 1 200 mm, or to trucks specifically designed to travel with an elevated load having a fork height up to and including 1 200 mm above ground level.

上海郜盟提示本标准不适用于升降操作人员位置在地面以上1200mm以下的卡车，也不适用于专门设计用于承载高于地面高度1200mm以上的高架货物的卡车。

It is not applicable to low-level order pickers with elevating operator’s position up to and including 1 200 mm lift height which can be equipped with an additional load lifting device having a maximum lift height of 1 800 mm from ground level.

上海郜盟提示但不适用于升降机操作员的位置最高可达及包括1 200毫米升降机高度的低级拣货机，而该升降机可配备一个额外的升降机装置，该装置的升降机高度从地面最高可达1 800毫米。

 

 

3、EN ISO 3691-3:2016拣货机CE认证相关标准

1）EN ISO 12100:2010 / Safety of machinery — General principles for design — Risk assessment and risk reduction (ISO 12100:2010) 机械安全。设计的一般原则。风险评估和风险降低

2）EN 1175: 2020 Safety of industrial trucks - Electrical/electronic requirements工业卡车安全-电气/电子要求

3） EN ISO 3691-1: 2015+A1: 2020 Industrial trucks - Safety requirements and verification - Part 1: Self-propelled industrial trucks, other than driverless trucks, variable-reach trucks and burden-carrier trucks - Amendment 1 (ISO 3691-1:2011/Amd 1:2020) 工业卡车。安全要求和验证。第1部分:无人驾驶卡车、可变伸距卡车和载重卡车以外的自行工业卡车。

4）EN 16307-1:2020 Industrial trucks - Safety requirements and verification - Part 1: Supplementary requirements for self-propelled industrial trucks, other than driverless trucks, variable-reach trucks and burden-carrier trucks工业卡车。安全要求和验证。第1部分:无人驾驶卡车、可变伸距卡车和载重卡车以外的自行式工业卡车的补充要求

 

4、EN ISO 3691-3:2016拣货机CE认证测试那些项目？

 

5、EN ISO 3691-3:2016拣货机CE认证流程？

载人升高的拣货机，人员提升高度超过3m，按照MD2006/42/EC附录IV的规定，需要申请EC-TYPE危险机械证书，由欧盟资质公告号机构进行样机审核。上海郜盟有公告号机构Notified Body认可的工程师可直接进行国内工厂的样机审核与测试，大大节省工厂差旅成本和时间成本，以及解决了近两年因为疫情原因国外审核员较难安排去工厂现场的问题。认证流程如下：

上海郜盟全程提供样机整改与技术资料整改技术指导，帮助工厂快速通过NB机构审核

 

 

6、EN ISO 3691-3:2016拣货机CE认证客户案例

 

上海郜盟顺利完成载人拣选车危险机械CE认证EC-TYPE审核

 

 

郜盟国际的服务

致力于中国制造全球化服务！

专业提供欧盟CE认证，美国FCC认证, 俄罗斯EAC认证, 沙特SASO认证, 英国UKCA认证, 尼日利亚SONCAP认证​等国际检测认证技术服务！标准培训！24小时咨询电话18018853504  13774495352

 

原创文章，严禁转载！！！